Announcement

Collapse
No announcement yet.

Do the wash test

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Do the wash test

    Most DTG printer makers will discuss the importance of performing a wash test to make sure all settings are producing the optimal results.

    It is important to understand that not all garments are created the same—even if they are comprised of the same fabrics and blends. Garment manufacturers use different weaving techniques, coloring dyes and treatment chemicals that can affect the washability of a print. Even the same exact brand and style of a garment can be made in multiple countries depending on the size or color of the garment, so pay close attention to where a garment is made.

    When performing a wash test, it is important to know and document all the settings used during the entire DTS process. These settings that should be recorded include:

    • Whether a pretreatment was used (and if so, how much fluid was applied and at what time/temperature it was cured),

    • The print settings used in the RIP/driver and

    • The settings used for curing the ink on to the garment.

    Wash performance

    When performing a wash test, I recommend that you actually print the settings on the garment. This will allow you to easily determine what settings you used to get the optimal results after performing the wash test.

    The sample graphic you choose to print can be anything, but I recommend something that contains gradients (i.e. a photograph) and solid color boxes. This will help determine whether both types of artwork will have the same washability. Also, keep in mind that both the front and back of the garment can be used, which minimizes the amount of garments needed to perform a wash test using multiple settings. If possible, print the artwork twice on the same garment to allow for one sample to be washed and the other to be used for comparison. Simply cut the garment into two pieces and put one of them through the laundry process.

    Different wash tests are required for light (uses CMYK inks only) and dark garments (uses CMYK and white inks). With dark garment printing, pay close attention to all the steps in the pretreating process. Changes to the type of cover paper used and heat press settings used to cure the pretreatment can definitely have an effect on the washability of the final printed artwork. A separate wash test is also necessary for polyester or poly blend garments.

    Cycling through

    The number of times you should put the garment through the laundry process will depend on customer expectations of how long the print should last. At a minimum, perform five complete laundry cycles. Many DTG users will put the test garment through anywhere 10 to 20 laundry cycles.

    Take pictures of all the samples next to the corresponding control sample between each laundry cycle. The pictures allow for a comparison to show how well the washed garment held up during each wash test. I recommend taking the pictures with the camera’s flash turned off, as the flash can change the way the colors look in a picture. Try to make sure you have the same amount of natural light in the room each time you take the pictures.

    Although some garment decorators will provide washing instructions (i.e. turn the garment inside-out, use cold water only, air dry only, etc.), the odds that the customers are going to follow these instructions are pretty low. So, to really provide a worst-case scenario for the wash test, I recommend using the standard washing habits of a male college student. This entails doing a full load of multiple types/colors of garments on the normal washing cycle settings using warm water. Then, put the garments into the dryer for a full 50 minutes or until the garments are completely dry to the touch. Do not use the “delicate” or “permanent press” settings for either the washing machine or dryer. If your sample garment is able to withstand this type of laundry cycle, you should have very little to worry about.

    Protect your image

    Repeat all the steps here until you find the appropriate settings that provide the desired results. Most DTG manufacturers/ distributors will provide recommended settings that will help you get started. However, you may need to experiment with pretreating and curing settings as these processes can vary.

    Periodically, you will want to re-run your wash test to make sure that none of the settings have unknowingly changed. Pay close attention to potential changes to the amount of pretreatment as well as the method of applying it, and to the temperature accuracy on your heat press.

    Although this many sound like a lot of steps to go through, the last thing any DTS user wants is a customer to return an order of shirts that washed out. The cost and time to reprint an average size job will far exceed what you would put into doing the wash test. In addition, the wash test process is an important part in protecting the reputation of your company.

    Source : https://printwearmag.com/features/ho...garment-prints
Working...
X